Hydraulic Solenoid Valve — How It Works, Types & Common Failures
Published 2026-09-10 · YXCHK Hydraulics engineering team · Manufacturer of ISO 4401 solenoid valves since 1994
Direct Answer
A hydraulic solenoid valve is an electrically actuated directional valve that routes pressurised oil by shifting a spool inside a bored body. YXCHK builds Rexroth- and Yuken-compatible versions in NG6, NG10 and NG16 sizes at 31.5 MPa and 21 MPa, each unit 100% individually pressure-tested.
- Function: routes flow to cylinders, motors or tank by spool position.
- Sizes: NG6 (ISO 4401-03), NG10 (ISO 4401-05), NG16 (ISO 4401-07).
- Pressure: 31.5 MPa Rexroth-type, 21 MPa Yuken-type.
- Coils: DC 24V (CG24) or AC 220V (AW220), IP65, DIN 43650 connector.
- Stock: 205 catalog models held ready.
What Is a Hydraulic Solenoid Valve?
A hydraulic solenoid valve is a directional control valve whose spool is moved by an electrical solenoid rather than by a hand lever, a cam, or pilot pressure. Oil enters at the pressure port (P), leaves to the tank port (T), and is directed to one of two actuator ports (A and B) depending on where the spool sits. Because the spool has to move to change the flow path, every solenoid valve is by definition a directional valve.
The reverse is not true. Directional valves can also be manual, lever, cam or pilot-operated; the solenoid version simply replaces the manual actuation with an electrical coil. In a typical industrial circuit a solenoid valve is the component that decides whether a cylinder extends, retracts, holds, or floats — and whether the pump is loaded or unloaded while it waits.
Terminology in the field is loose. "Solenoid valve", "directional valve" and "directional control valve" are often used for the same hardware; "DCV" and "4-way valve" are shorthand for the same four-port device. When reading a supplier catalogue, the reliable signal is the port count and the number of spool positions, not the label on the page.
How It Works: Coil, Armature, Spool, Ports
The chain from electrical command to oil movement has four links. Understanding them in order is what makes fault-finding straightforward later.
1. Electrical signal. A PLC output, relay or manual switch energises the coil at its rated voltage — typically DC 24V or AC 220V. The coil is a separate assembly that slides onto the valve tube and can be replaced without opening the hydraulic circuit.
2. Magnetic field. Current through the coil generates a magnetic field inside the tube. The field is proportional to current, which is why a coil fed at the wrong voltage either fails to shift the spool or overheats.
3. Armature and push pin. The field pulls the armature towards the pole piece. The armature drives a push pin against the end of the spool, converting the magnetic force into linear travel of a few millimetres.
4. Spool and ports. The spool is a hardened, ground steel shaft with lands and grooves machined to fit the bore with a clearance measured in microns. As it slides between positions, the lands uncover and cover the port passages, routing pressure to A or B, and return flow back to T. When the solenoid is de-energised, the centring spring returns the spool to the neutral position — and it is the neutral position that determines whether the load holds, drifts or floats.
Wet-pin or dry-pin: in a wet-pin design the armature moves inside hydraulic oil, which lubricates it and damps movement; in a dry-pin design the armature runs dry behind a seal. Wet-pin is now the norm on industrial NG6 and NG10 valves because it removes the dynamic seal as a wear item.
The Five Configurations: 2/2, 3/2, 3/3, 4/2, 4/3
Valve nomenclature is written as "ways / positions" — the number of flow paths the valve can connect, and the number of distinct spool positions it can sit in. Both numbers matter when reading a datasheet or matching a replacement.
| Configuration | Ports | Positions | Typical use |
|---|---|---|---|
| 2/2 | P, T (or P, A) | 2 | On/off isolation, dump and vent circuits |
| 3/2 | P, T, A | 2 | Single-acting cylinders, clamping, pilot supply |
| 3/3 | P, T, A | 3 | Single-acting cylinder with a defined neutral state |
| 4/2 | P, T, A, B | 2 | Double-acting cylinder without a neutral position |
| 4/3 | P, T, A, B | 3 | Double-acting cylinder with a selectable neutral function |
The 4/3 valve is the workhorse of industrial hydraulics, and it is the configuration where selection mistakes concentrate: the same body can be supplied with eight or more different neutral behaviours, and the choice changes whether the cylinder holds a load, drifts, or floats freely while the pump unloads. That decision is covered step by step in our how to select a directional valve guide.
A 2/2 or 3/2 valve does not have a neutral position in the same sense — with only two positions there is no centre to define, so the load-holding question is answered by the circuit (a pilot-operated check valve, for example) rather than by the spool itself.
Spool Function Codes Compared (Rexroth ↔ Yuken ↔ Shanghai-type)
The spool code letter tells you what happens to the four ports when the valve is de-energised. Two suppliers can use the same letter for different behaviour, and different letters for the same behaviour — so always compare the centre condition, never the letter alone.
| Rexroth | Centre condition | Yuken | Shanghai-type |
|---|---|---|---|
| E | All four ports closed — holds load | 3C2 | O |
| G | P→T, A & B blocked — tandem, pump unloads | 3C60 | M |
| H | All ports open (P, A, B, T interconnected) | 3C3 | H |
| J | P blocked, A & B to T — float centre | 3C4 | Y |
| L | All four ports open to T — float | 3C12 | N |
| M | P, A, B connected; T blocked | 3C9 | P |
| U | P→A via check, B→T | 3C10 | — |
| F | P→B via check, A→T | 3C5 | — |
The two that get confused most often. J (Yuken 3C4) is a float centre with the pump still loaded: the spool blocks P while opening A and B to tank, so the actuator is free to move under external force while full system pressure remains available to other branches. G (Yuken 3C60) is the opposite trade: P is connected to T so the pump unloads, but A and B are blocked, so the cylinder holds its position. If a machine holds its load while idling and the oil stays cool, it is almost certainly running G or E — not J.
Wet-Pin vs Dry-Pin, AC vs DC Coils
Two independent choices sit on top of the spool decision, and both are frequently specified by habit rather than by requirement.
Wet-pin. The armature runs immersed in hydraulic oil inside the valve tube. There is no dynamic seal between the magnetic circuit and the oil, so there is one less wear item, the movement is hydraulically damped, and the valve is quieter. Practically every industrial NG6 and NG10 solenoid valve sold today — including all YXCHK Rexroth-type and Yuken-type models — is wet-pin.
Dry-pin. The armature operates in air behind a seal. It survives dirty or non-lubricating fluids better in some legacy designs, but the seal is a wear item and the valve is noisier. Dry-pin designs are mostly encountered on older equipment and on specialist circuits.
DC 24V is the default choice on PLC-controlled machinery. A DC coil draws essentially constant current regardless of armature position, so a jammed spool simply means the valve does not shift — the coil is not damaged. It also switches faster, because there is no magnetising inrush to build and collapse.
AC 220V coils draw a large inrush current that falls once the armature has pulled fully in. On an AC valve the same jam leaves the coil sitting at inrush current, and it can overheat and burn out within minutes. AC is still correct for legacy relay-controlled panels and for long cable runs where voltage drop matters, but it should be a deliberate choice rather than a default.
The coil is a replaceable part on both designs. In the Rexroth-type numbering, CG24 denotes a DC 24V coil and AW220 an AC 220V coil; the same body accepts either, provided the supply matches. Both are terminated on the industry-standard DIN 43650 connector, which is exactly why the connector type must never be used to infer the voltage — read the coil body.
Six Failure Modes and What Causes Them
1. Coil burnout. Usually a symptom, not the cause — sustained over-voltage, a shorted coil, or a spool that is stuck and keeps the coil energised at high current. If a replacement coil fails again, check the spool first.
2. Contamination and silting. The most common root cause. Particles and varnish build up in the spool clearance until the valve no longer centres. System filtration and oil condition matter more than valve brand here.
3. Spool sticking. The valve shifts slowly or not at all. Typically contamination or a bent/varnished spool; occasionally a damaged bore from a previous repair.
4. Seal and O-ring degradation. External weeping or internal bypass. Heat, incompatible fluid, or simply age. Seal kits are the economical fix — unless the spool/bore pair is already worn.
5. Low or incorrect coil voltage. The valve hums but does not shift cleanly. Verify supply voltage at the coil under load, not at the panel.
6. Water ingress at the connector. Corrosion at the DIN 43650 plug causes intermittent operation. IP65-rated connectors and correct cable glands prevent it.
If the same valve has failed its function test three times in twelve months, the spool and bore are typically past economical recovery — see the repair vs replace decision guide.
How to Read a Model Code (Worked Example)
Take a real catalogue entry: 4WE6E60/CG24N9Z5L. It reads left to right as five separate decisions.
| Segment | Meaning |
|---|---|
| 4WE6 | Four-way directional valve, solenoid operated, NG6 / ISO 4401-03 mounting face |
| E | Spool function E — all four ports closed in the neutral position (holds load) |
| 60 | Series / design number — defines the internal geometry and the spare-parts generation |
| CG24 | Coil: CG = DC coil, 24 = 24 volts |
| N9 | DIN 43650 connector with indicator light, no integral diode |
| Z5L | Manual override and seal variant (Z5 = override, L = NBR seals) |
This is why a replacement has to be specified by behaviour rather than by appearance. Two valves that look identical and share the same 4WE6 prefix can differ in the letter that decides whether a press holds its clamp or drops it. If you are decoding a Rexroth part number to find a compatible alternative, our Rexroth 4WE6 equivalents page maps each segment one to one — and the 4WE6 cross reference table covers model-level matching across brands.
Repair or Replace?
Most solenoid valve faults are cheap to fix once the cause is identified: a coil, a seal kit or a connector. The economics change when the fault returns. A practical rule used on maintenance floors is the three-strike rule: if the same valve fails its function test three times within twelve months, the spool and bore are usually worn beyond the point where another seal kit will hold, and the cost of downtime starts to exceed the cost of a replacement.
A second signal is performance: if the cylinder has begun to drift, if cycle times have lengthened, or if the valve needs a higher command pressure to shift than it did when new, the clearance has opened up and no external adjustment will close it again.
If the decision is to replace, the practical questions are the mounting face, the spool function and the coil voltage — in that order. For Yuken-type equipment, our Yuken DSG-02 replacements page lists the models that bolt on directly, and the repair vs replace guide works through the cost comparison in detail.
Frequently Asked Questions
What is the difference between a hydraulic solenoid valve and a directional valve?
Every hydraulic solenoid valve is a directional valve, but not every directional valve is solenoid-operated. Directional valves can also be manual, lever, cam or pilot operated; the solenoid version replaces the manual actuation with an electrical coil.
How do I know if a solenoid valve is 24V DC or 220V AC?
Read the coil code on the nameplate. In the Rexroth-type system CG24 means DC 24V and AW220 means AC 220V; the coil is a separate part and can be changed without replacing the valve body.
Can I replace a Rexroth 4WE6 with a different brand?
Yes, if the mounting face (ISO 4401-03 / NG6), spool function, coil voltage and pressure class match. Spool function must match by behaviour, not by letter — see the cross-brand spool table above.
Why does my solenoid valve get hot?
Normal coil surface temperature rises with duty cycle, but excessive heat usually indicates over-voltage or a mechanically stuck spool keeping current high. Compare coil resistance against the datasheet before replacing anything.
Related Resources
Directional Valve Selection Guide
ISO 4401 sizes, spool logic, coil voltage and flow verification in five steps.
Rexroth 4WE6 Equivalents
Segment-by-segment model mapping and compatibility checks.
Yuken DSG-02 Replacements
Drop-in equivalents for the 3C2, 3C4 and 3C60 spool variants.
4WE6 Replacement Guide
Model-code decoding and the three-step compatibility check.
Repair vs Replace Guide
Decision framework and cost comparison for ageing valves.
Full Product Catalog
205 SKUs across NG6, NG10 and pilot-operated series.