Home Full Catalog 4WE10C30B/CG24N9Z5L
4WE10C30B/CG24N9Z5L - Hydraulic Solenoid Valve by YXCHK
4WE10 Series

4WE10C30B/CG24N9Z5L

Hydraulic Solenoid Valve model 4WE10C30B/CG24N9Z5L - a Rexroth 4WE10 compatible hydraulic valve from YXCHK. Rated 31.5 MPa max pressure and 120 L/min max flow with DC 24V, AC 220V. 100% factory tested, 1-year warranty.

Max Pressure 31.5 MPa
Max Flow 120 L/min

Technical Datasheet

Specification ParameterTechnical Value
Nominal SizeNG10 / Cetop 5 / ISO 4401-05
Max Working Pressure31.5 MPa
Max T-Port Pressure16 MPa
Max Flow Rate120 L/min
Coil / ActuationDC 24V, AC 220V
Solenoid TypeWet solenoid, low-noise, N9 manual override
Spool FunctionsC — not published in our spool table — drawing on request
Hydraulic FluidMineral oil HL/HLP per DIN 51524

Centre Condition & Cross-Reference

Spool FunctionC
De-energised Flow Pathnot published in our spool table — drawing on request
Yuken Equivalentequivalent code on request

Spool code C is not covered by the published spool table on this site, so no port-connection pattern is restated here from a neighbouring code; the drawing for this exact code is sent with the quotation. Structurally the valve is the standard 4WE10 body. This entry covers the single-letter C spool.

Cross Reference

Drop-in replacement for Bosch Rexroth 4WE10 / 3WE10 series. NG10 / Cetop 5 / ISO 4401-05 mounting, 100% interchangeable.

YXCHK Model4WE10C30B/CG24N9Z5L
ReplacesRexroth 4WE10
Mounting StandardNG10 / Cetop 5 / ISO 4401-05
Voltage OptionsDC 24V, AC 220V

Spool Function & Control

Model 4WE10C30B/CG24N9Z5L is an NG10 (Cetop 5, ISO 4401-05) wet-armature solenoid directional valve engineered as a direct replacement for the Bosch Rexroth 4WE10 / 3WE10 series on the ISO 4401-05 mounting surface. It is one of 205 catalogued YXCHK models, and this page documents a single spool function — C — rather than the whole series. the port-connection pattern for spool code C is not published in the spool table on this site. No pattern is copied across from a neighbouring code to fill the gap. The 10 mm bore with a hardened, precision-ground spool delivers stable high-flow switching with minimal pressure ripple, and wet solenoid construction keeps the coil in oil for heat dissipation and a design service life beyond reliables.

Mounting & Electrical

4WE10C30B/CG24N9Z5L bolts onto any ISO 4401-05 subplate or manifold without an adapter. The CG24 coil is the 24 V DC wet-armature solenoid: current draw stays steady through the whole stroke, so pull-in and holding force do not change as the spool travels, which keeps shift timing repeatable on a large 10 mm bore. Termination is a Z5L DIN 43650 plug with indicator light, IP65 against dust and oil mist, plus the N9 manual override for hand operation with the power off. Rated 31.5 MPa working pressure, 120 L/min flow and 16 MPa maximum T-port back pressure; fluid is mineral oil HL/HLP per DIN 51524.

Quality & Reliability

Every valve leaves the Taizhou plant only after a full bench test - coil function, internal leakage and a pressure hold at 31.5 MPa - and each result is filed against its production batch, so a serial number can still be traced back years later. Bodies are machined from cast iron on CNC centres to ISO 4401 mounting-face tolerances. The range carries Intertek certification, a one-year replacement warranty and an eight-year design life; standard orders ship from Ningbo Port inside seven working days, and the minimum order is a single piece.

Where It Fits

These valves go into circuits that move a lot of oil at pressure: forging press main rams, mould-clamp and ejector drives, compactor rams, winch motors on deck. With a 10 mm bore and a 120 L/min flow rating the body carries that volume without starving parallel actuators, and the wet solenoid keeps response quiet and repeatable under continuous cycling. Give us the model code you are replacing and the cross-reference is confirmed inside 24 hours, at no charge.

Typical Applications

  • Heavy forging presses - high-flow directional control
  • Plastic machinery - injection molding clamp systems
  • Waste compactors - high-power reciprocating actuators

Quality & Standards

Every YXCHK valve is 100% factory tested (electrical, leakage and max pressure) before shipment. Mounting patterns comply with ISO 4401 / DIN 24340 international standards, and the design follows the ISO 4401 hydraulic valve interface specification, matching the original Bosch Rexroth and Yuken dimensional standards.

Products are Intertek certified for high-pressure reliability, backed by a 1-year replacement warranty and reliable design service life. Standard orders ship from regular stock at Ningbo Port.

Related Models