Home Full Catalog 4WE10E30B/AW220N9Z5L
4WE10E30B/AW220N9Z5L - Hydraulic Solenoid Valve by YXCHK
4WE10 Series

4WE10E30B/AW220N9Z5L

Hydraulic Solenoid Valve model 4WE10E30B/AW220N9Z5L - a Rexroth 4WE10 compatible hydraulic valve from YXCHK. Rated 31.5 MPa max pressure and 120 L/min max flow with DC 24V, AC 220V. 100% factory tested, 1-year warranty.

Max Pressure 31.5 MPa
Max Flow 120 L/min

Technical Datasheet

Specification ParameterTechnical Value
Nominal SizeNG10 / Cetop 5 / ISO 4401-05
Max Working Pressure31.5 MPa
Max T-Port Pressure16 MPa
Max Flow Rate120 L/min
Coil / ActuationDC 24V, AC 220V
Solenoid TypeWet solenoid, low-noise, N9 manual override
Spool FunctionsE — all ports blocked (P, A, B and T mutually isolated)
Hydraulic FluidMineral oil HL/HLP per DIN 51524

Centre Condition & Cross-Reference

Spool FunctionE
De-energised Flow Pathall ports blocked (P, A, B and T mutually isolated)
Yuken Equivalent3C2

With both solenoids de-energised, P, A, B and T are mutually isolated. Pressure cannot reach either work port and neither work port can drain, so a cylinder or motor connected to A and B stays locked while the pressure line is sealed inside the valve. This is the blocking centre: the load is held after the pump stops and nothing drifts while the valve sits centred.

Cross Reference

Drop-in replacement for Bosch Rexroth 4WE10 / 3WE10 series. NG10 / Cetop 5 / ISO 4401-05 mounting, 100% interchangeable.

YXCHK Model4WE10E30B/AW220N9Z5L
ReplacesRexroth 4WE10
Mounting StandardNG10 / Cetop 5 / ISO 4401-05
Voltage OptionsDC 24V, AC 220V

Spool Function & Control

Model 4WE10E30B/AW220N9Z5L is an NG10 (Cetop 5, ISO 4401-05) wet-armature solenoid directional valve engineered as a direct replacement for the Bosch Rexroth 4WE10 / 3WE10 series on the ISO 4401-05 mounting surface. It is one of 205 catalogued YXCHK models, and this page documents a single spool function — E — rather than the whole series. With both solenoids de-energised, P, A, B and T are mutually isolated. Pressure cannot reach either work port and neither work port can drain back to tank. The 10 mm bore with a hardened, precision-ground spool delivers stable high-flow switching with minimal pressure ripple, and wet solenoid construction keeps the coil in oil for heat dissipation and a design service life beyond reliables.

Mounting & Electrical

4WE10E30B/AW220N9Z5L fits the same ISO 4401-05 interface, hole pattern unchanged. The AW220 coil is the 220 V AC wet-armature solenoid: an AC coil draws a high inrush current on pull-in and then a much lower holding current once the armature seats, so the seating stroke must not be obstructed or the valve will chatter on a 10 mm bore. The coil terminates in a Z5L DIN 43650 plug with indicator light, IP65 rated, and the N9 manual override covers commissioning and fault-finding. Working pressure is 31.5 MPa, rated flow 120 L/min, maximum T-port back pressure 16 MPa, with mineral oil HL/HLP to DIN 51524.

Quality & Reliability

Before packing, each unit is energised, checked for internal leakage and pressure-tested to 31.5 MPa on the test bench in Taizhou; the readings stay on file by batch, which is what lets a warranty question be answered with data instead of guesswork. Cast-iron bodies are CNC-machined to a tolerance of +/- ISO 4401 mounting-face tolerances. Intertek certification, a one-year replacement warranty and an eight-year design life apply across the range. Shipments leave Ningbo Port within seven working days, and one piece is enough to place an order.

Where It Fits

The circuit this valve serves is a high-volume one: forging press main rams, mould-clamp and ejector drives, compactor rams, winch motors. Rated at 31.5 MPa and 120 L/min through an NG10 bore, it keeps several actuators supplied from one power unit without the pressure drop a smaller body would introduce, and the wet solenoid holds response quiet and repeatable in continuous cycling. Send the original model code and an engineer confirms the cross-reference within 24 hours, free of charge.

Typical Applications

  • Heavy forging presses - high-flow directional control
  • Plastic machinery - injection molding clamp systems
  • Waste compactors - high-power reciprocating actuators

Quality & Standards

Every YXCHK valve is 100% factory tested (electrical, leakage and max pressure) before shipment. Mounting patterns comply with ISO 4401 / DIN 24340 international standards, and the design follows the ISO 4401 hydraulic valve interface specification, matching the original Bosch Rexroth and Yuken dimensional standards.

Products are Intertek certified for high-pressure reliability, backed by a 1-year replacement warranty and reliable design service life. Standard orders ship from regular stock at Ningbo Port.

Related Models