Home Full Catalog 4WE10F30B/AW220N9Z5L
4WE10F30B/AW220N9Z5L - Hydraulic Solenoid Valve by YXCHK
4WE10 Series

4WE10F30B/AW220N9Z5L

Hydraulic Solenoid Valve model 4WE10F30B/AW220N9Z5L - a Rexroth 4WE10 compatible hydraulic valve from YXCHK. Rated 31.5 MPa max pressure and 120 L/min max flow with DC 24V, AC 220V. 100% factory tested, 1-year warranty.

Max Pressure 31.5 MPa
Max Flow 120 L/min

Technical Datasheet

Specification ParameterTechnical Value
Nominal SizeNG10 / Cetop 5 / ISO 4401-05
Max Working Pressure31.5 MPa
Max T-Port Pressure16 MPa
Max Flow Rate120 L/min
Coil / ActuationDC 24V, AC 220V
Solenoid TypeWet solenoid, low-noise, N9 manual override
Spool FunctionsF — A, P and T interconnected, B blocked
Hydraulic FluidMineral oil HL/HLP per DIN 51524

Centre Condition & Cross-Reference

Spool FunctionF
De-energised Flow PathA, P and T interconnected, B blocked
Yuken Equivalent3C5

A, P and T form one connected path while B is blocked. Flow entering P can leave through A and continue on to T, and the B work line stays sealed; the net effect at centre is a vented A port with the pump tied to it and to tank at the same time.

Cross Reference

Drop-in replacement for Bosch Rexroth 4WE10 / 3WE10 series. NG10 / Cetop 5 / ISO 4401-05 mounting, 100% interchangeable.

YXCHK Model4WE10F30B/AW220N9Z5L
ReplacesRexroth 4WE10
Mounting StandardNG10 / Cetop 5 / ISO 4401-05
Voltage OptionsDC 24V, AC 220V

Spool Function & Control

Model 4WE10F30B/AW220N9Z5L is an NG10 (Cetop 5, ISO 4401-05) wet-armature solenoid directional valve engineered as a direct replacement for the Bosch Rexroth 4WE10 / 3WE10 series on the ISO 4401-05 mounting surface. It is one of 205 catalogued YXCHK models, and this page documents a single spool function — F — rather than the whole series. A, P and T form one connected path while B is blocked. Flow entering P can leave through A and continue to T while the B line stays sealed. The 10 mm bore with a hardened, precision-ground spool delivers stable high-flow switching with minimal pressure ripple, and wet solenoid construction keeps the coil in oil for heat dissipation and a design service life beyond reliables.

Mounting & Electrical

4WE10F30B/AW220N9Z5L fits the same ISO 4401-05 interface, hole pattern unchanged. The AW220 coil is the 220 V AC wet-armature solenoid: an AC coil draws a high inrush current on pull-in and then a much lower holding current once the armature seats, so the seating stroke must not be obstructed or the valve will chatter on a 10 mm bore. The coil terminates in a Z5L DIN 43650 plug with indicator light, IP65 rated, and the N9 manual override covers commissioning and fault-finding. Working pressure is 31.5 MPa, rated flow 120 L/min, maximum T-port back pressure 16 MPa, with mineral oil HL/HLP to DIN 51524.

Quality & Reliability

Quality control at the Taizhou factory is 100% end-of-line: electrical operation, internal leakage and a 31.5 MPa pressure test, with the record archived per batch for traceability. The valve body is cast iron, CNC-machined to ISO 4401 mounting-face tolerances. Every model is Intertek certified and covered by a one-year replacement warranty against an eight-year design life, and orders of one piece or more are dispatched from Ningbo Port within seven working days.

Where It Fits

Typical service is heavy machinery with large actuators - forging presses, injection moulding clamp systems, industrial compactors and marine winching. The valve is rated 31.5 MPa with 120 L/min through an NG10 bore, which gives the flow headroom multi-actuator circuits need, while the wet armature keeps operation quiet and repeatable under continuous cycling. The cross-reference is confirmed within 24 hours from the original model code, free of charge.

Typical Applications

  • Heavy forging presses - high-flow directional control
  • Plastic machinery - injection molding clamp systems
  • Waste compactors - high-power reciprocating actuators

Quality & Standards

Every YXCHK valve is 100% factory tested (electrical, leakage and max pressure) before shipment. Mounting patterns comply with ISO 4401 / DIN 24340 international standards, and the design follows the ISO 4401 hydraulic valve interface specification, matching the original Bosch Rexroth and Yuken dimensional standards.

Products are Intertek certified for high-pressure reliability, backed by a 1-year replacement warranty and reliable design service life. Standard orders ship from regular stock at Ningbo Port.

Related Models