4WE10G30B/AW220N9Z5L
Hydraulic Solenoid Valve model 4WE10G30B/AW220N9Z5L - a Rexroth 4WE10 compatible hydraulic valve from YXCHK. Rated 31.5 MPa max pressure and 120 L/min max flow with DC 24V, AC 220V. 100% factory tested, 1-year warranty.
Technical Datasheet
| Specification Parameter | Technical Value |
|---|---|
| Nominal Size | NG10 / Cetop 5 / ISO 4401-05 |
| Max Working Pressure | 31.5 MPa |
| Max T-Port Pressure | 16 MPa |
| Max Flow Rate | 120 L/min |
| Coil / Actuation | DC 24V, AC 220V |
| Solenoid Type | Wet solenoid, low-noise, N9 manual override |
| Spool Functions | G — P → T open, A and B blocked |
| Hydraulic Fluid | Mineral oil HL/HLP per DIN 51524 |
Centre Condition & Cross-Reference
| Spool Function | G |
| De-energised Flow Path | P → T open, A and B blocked |
| Yuken Equivalent | 3C60 |
De-energised, P is connected to T while A and B are blocked. Pump flow passes straight back to the tank through the centre, so the power unit is unloaded whenever the valve sits in its rest position, and both work lines stay sealed so the actuator holds where it was left. That combination - pump unloaded, load held - is what the tandem centre is chosen for.
Cross Reference
Drop-in replacement for Bosch Rexroth 4WE10 / 3WE10 series. NG10 / Cetop 5 / ISO 4401-05 mounting, 100% interchangeable.
| YXCHK Model | 4WE10G30B/AW220N9Z5L |
| Replaces | Rexroth 4WE10 |
| Mounting Standard | NG10 / Cetop 5 / ISO 4401-05 |
| Voltage Options | DC 24V, AC 220V |
Spool Function & Control
Model 4WE10G30B/AW220N9Z5L is an NG10 (Cetop 5, ISO 4401-05) wet-armature solenoid directional valve engineered as a direct replacement for the Bosch Rexroth 4WE10 / 3WE10 series on the ISO 4401-05 mounting surface. It is one of 205 catalogued YXCHK models, and this page documents a single spool function — G — rather than the whole series. P is connected to T while A and B are blocked. Pump flow returns to the tank through the centre while both work lines stay sealed. The 10 mm bore with a hardened, precision-ground spool delivers stable high-flow switching with minimal pressure ripple, and wet solenoid construction keeps the coil in oil for heat dissipation and a design service life beyond reliables.
Mounting & Electrical
4WE10G30B/AW220N9Z5L fits the same ISO 4401-05 interface, hole pattern unchanged. The AW220 coil is the 220 V AC wet-armature solenoid: an AC coil draws a high inrush current on pull-in and then a much lower holding current once the armature seats, so the seating stroke must not be obstructed or the valve will chatter on a 10 mm bore. The coil terminates in a Z5L DIN 43650 plug with indicator light, IP65 rated, and the N9 manual override covers commissioning and fault-finding. Working pressure is 31.5 MPa, rated flow 120 L/min, maximum T-port back pressure 16 MPa, with mineral oil HL/HLP to DIN 51524.
Quality & Reliability
Quality control at the Taizhou factory is 100% end-of-line: electrical operation, internal leakage and a 31.5 MPa pressure test, with the record archived per batch for traceability. The valve body is cast iron, CNC-machined to ISO 4401 mounting-face tolerances. Every model is Intertek certified and covered by a one-year replacement warranty against an eight-year design life, and orders of one piece or more are dispatched from Ningbo Port within seven working days.
Where It Fits
The circuit this valve serves is a high-volume one: forging press main rams, mould-clamp and ejector drives, compactor rams, winch motors. Rated at 31.5 MPa and 120 L/min through an NG10 bore, it keeps several actuators supplied from one power unit without the pressure drop a smaller body would introduce, and the wet solenoid holds response quiet and repeatable in continuous cycling. Send the original model code and an engineer confirms the cross-reference within 24 hours, free of charge.
Typical Applications
- Heavy forging presses - high-flow directional control
- Plastic machinery - injection molding clamp systems
- Waste compactors - high-power reciprocating actuators
Quality & Standards
Every YXCHK valve is 100% factory tested (electrical, leakage and max pressure) before shipment. Mounting patterns comply with ISO 4401 / DIN 24340 international standards, and the design follows the ISO 4401 hydraulic valve interface specification, matching the original Bosch Rexroth and Yuken dimensional standards.
Products are Intertek certified for high-pressure reliability, backed by a 1-year replacement warranty and reliable design service life. Standard orders ship from regular stock at Ningbo Port.
Related Models
More 4WE10 series models
Also in Rexroth-style directional valves