4WE10GA30B/AW220N9Z5L
Hydraulic Solenoid Valve model 4WE10GA30B/AW220N9Z5L - a Rexroth 4WE10 compatible hydraulic valve from YXCHK. Rated 31.5 MPa max pressure and 120 L/min max flow with DC 24V, AC 220V. 100% factory tested, 1-year warranty.
Technical Datasheet
| Specification Parameter | Technical Value |
|---|---|
| Nominal Size | NG10 / Cetop 5 / ISO 4401-05 |
| Max Working Pressure | 31.5 MPa |
| Max T-Port Pressure | 16 MPa |
| Max Flow Rate | 120 L/min |
| Coil / Actuation | DC 24V, AC 220V |
| Solenoid Type | Wet solenoid, low-noise, N9 manual override |
| Spool Functions | GA — P → T open, A and B blocked |
| Hydraulic Fluid | Mineral oil HL/HLP per DIN 51524 |
Centre Condition & Cross-Reference
| Spool Function | GA |
| De-energised Flow Path | P → T open, A and B blocked |
| Yuken Equivalent | equivalent code on request |
GA is the single-solenoid (spring-return) conversion of spool G and runs the same spool. At centre the flow path is unchanged: P is connected to T while A and B are blocked, so pump flow returns to the tank through the centre and both work lines stay sealed. One solenoid shifts the spool and the spring returns it to this centre position when power is removed. Only one coil is fitted, so the wiring is a single solenoid lead, and the valve drops back to this centre as soon as that coil is switched off.
Cross Reference
Drop-in replacement for Bosch Rexroth 4WE10 / 3WE10 series. NG10 / Cetop 5 / ISO 4401-05 mounting, 100% interchangeable.
| YXCHK Model | 4WE10GA30B/AW220N9Z5L |
| Replaces | Rexroth 4WE10 |
| Mounting Standard | NG10 / Cetop 5 / ISO 4401-05 |
| Voltage Options | DC 24V, AC 220V |
Spool Function & Control
Model 4WE10GA30B/AW220N9Z5L is an NG10 (Cetop 5, ISO 4401-05) wet-armature solenoid directional valve engineered as a direct replacement for the Bosch Rexroth 4WE10 / 3WE10 series on the ISO 4401-05 mounting surface. It is one of 205 catalogued YXCHK models, and this page documents a single spool function — GA — rather than the whole series. P is connected to T while A and B are blocked, the same centre as spool G. Pump flow returns to the tank through the centre while both work lines stay sealed. The 10 mm bore with a hardened, precision-ground spool delivers stable high-flow switching with minimal pressure ripple, and wet solenoid construction keeps the coil in oil for heat dissipation and a design service life beyond reliables.
Mounting & Electrical
4WE10GA30B/AW220N9Z5L fits the same ISO 4401-05 interface, hole pattern unchanged. The AW220 coil is the 220 V AC wet-armature solenoid: an AC coil draws a high inrush current on pull-in and then a much lower holding current once the armature seats, so the seating stroke must not be obstructed or the valve will chatter on a 10 mm bore. The coil terminates in a Z5L DIN 43650 plug with indicator light, IP65 rated, and the N9 manual override covers commissioning and fault-finding. Working pressure is 31.5 MPa, rated flow 120 L/min, maximum T-port back pressure 16 MPa, with mineral oil HL/HLP to DIN 51524.
Quality & Reliability
Each unit is run on the test bench in Taizhou before it is packed: the coil is energised, internal leakage is measured and the assembly is held at 31.5 MPa, and the sheet from that run stays attached to the batch record, so the history of any serial number survives. Valve bodies are cast iron, finished on CNC centres to a tolerance of +/- ISO 4401 mounting-face tolerances. Intertek certification, a one-year replacement warranty and an eight-year design life cover the range, orders are despatched from Ningbo Port within seven working days, and a single piece is a valid order quantity.
Where It Fits
This valve is specified for high-flow, high-pressure machinery: heavy forging presses, injection moulding clamp systems, large waste compactors and marine winch circuits. The NG10 bore leaves ample flow margin for multi-actuator systems, and the wet solenoid keeps noise low and service life long under continuous duty. Send the original model code and our engineers confirm the cross-reference inside 24 hours, free of charge.
Typical Applications
- Heavy forging presses - high-flow directional control
- Plastic machinery - injection molding clamp systems
- Waste compactors - high-power reciprocating actuators
Quality & Standards
Every YXCHK valve is 100% factory tested (electrical, leakage and max pressure) before shipment. Mounting patterns comply with ISO 4401 / DIN 24340 international standards, and the design follows the ISO 4401 hydraulic valve interface specification, matching the original Bosch Rexroth and Yuken dimensional standards.
Products are Intertek certified for high-pressure reliability, backed by a 1-year replacement warranty and reliable design service life. Standard orders ship from regular stock at Ningbo Port.
Related Models
More 4WE10 series models
Also in Rexroth-style directional valves