4WE10JA30B/AW220N9Z5L
Hydraulic Solenoid Valve model 4WE10JA30B/AW220N9Z5L - a Rexroth 4WE10 compatible hydraulic valve from YXCHK. Rated 31.5 MPa max pressure and 120 L/min max flow with DC 24V, AC 220V. 100% factory tested, 1-year warranty.
Technical Datasheet
| Specification Parameter | Technical Value |
|---|---|
| Nominal Size | NG10 / Cetop 5 / ISO 4401-05 |
| Max Working Pressure | 31.5 MPa |
| Max T-Port Pressure | 16 MPa |
| Max Flow Rate | 120 L/min |
| Coil / Actuation | DC 24V, AC 220V |
| Solenoid Type | Wet solenoid, low-noise, N9 manual override |
| Spool Functions | JA — P blocked, A and B open to T |
| Hydraulic Fluid | Mineral oil HL/HLP per DIN 51524 |
Centre Condition & Cross-Reference
| Spool Function | JA |
| De-energised Flow Path | P blocked, A and B open to T |
| Yuken Equivalent | equivalent code on request |
JA is the single-solenoid conversion of spool J, again on the same spool. At centre P is blocked while A and B are both open to T, so the pump is isolated from the circuit and both work lines drain to tank; the actuator can settle instead of being driven. The spring restores this float centre as soon as the coil is de-energised, so a single coil is enough to hold the working position and no second solenoid is needed.
Cross Reference
Drop-in replacement for Bosch Rexroth 4WE10 / 3WE10 series. NG10 / Cetop 5 / ISO 4401-05 mounting, 100% interchangeable.
| YXCHK Model | 4WE10JA30B/AW220N9Z5L |
| Replaces | Rexroth 4WE10 |
| Mounting Standard | NG10 / Cetop 5 / ISO 4401-05 |
| Voltage Options | DC 24V, AC 220V |
Spool Function & Control
Model 4WE10JA30B/AW220N9Z5L is an NG10 (Cetop 5, ISO 4401-05) wet-armature solenoid directional valve engineered as a direct replacement for the Bosch Rexroth 4WE10 / 3WE10 series on the ISO 4401-05 mounting surface. It is one of 205 catalogued YXCHK models, and this page documents a single spool function — JA — rather than the whole series. P is blocked while A and B are both open to T, the same centre as spool J. The pump is isolated from the circuit and both work lines drain to tank. The 10 mm bore with a hardened, precision-ground spool delivers stable high-flow switching with minimal pressure ripple, and wet solenoid construction keeps the coil in oil for heat dissipation and a design service life beyond reliables.
Mounting & Electrical
4WE10JA30B/AW220N9Z5L fits the same ISO 4401-05 interface, hole pattern unchanged. The AW220 coil is the 220 V AC wet-armature solenoid: an AC coil draws a high inrush current on pull-in and then a much lower holding current once the armature seats, so the seating stroke must not be obstructed or the valve will chatter on a 10 mm bore. The coil terminates in a Z5L DIN 43650 plug with indicator light, IP65 rated, and the N9 manual override covers commissioning and fault-finding. Working pressure is 31.5 MPa, rated flow 120 L/min, maximum T-port back pressure 16 MPa, with mineral oil HL/HLP to DIN 51524.
Quality & Reliability
Every valve leaves the Taizhou plant only after a full bench test - coil function, internal leakage and a pressure hold at 31.5 MPa - and each result is filed against its production batch, so a serial number can still be traced back years later. Bodies are machined from cast iron on CNC centres to ISO 4401 mounting-face tolerances. The range carries Intertek certification, a one-year replacement warranty and an eight-year design life; standard orders ship from Ningbo Port inside seven working days, and the minimum order is a single piece.
Where It Fits
This valve is specified for high-flow, high-pressure machinery: heavy forging presses, injection moulding clamp systems, large waste compactors and marine winch circuits. The NG10 bore leaves ample flow margin for multi-actuator systems, and the wet solenoid keeps noise low and service life long under continuous duty. Send the original model code and our engineers confirm the cross-reference inside 24 hours, free of charge.
Typical Applications
- Heavy forging presses - high-flow directional control
- Plastic machinery - injection molding clamp systems
- Waste compactors - high-power reciprocating actuators
Quality & Standards
Every YXCHK valve is 100% factory tested (electrical, leakage and max pressure) before shipment. Mounting patterns comply with ISO 4401 / DIN 24340 international standards, and the design follows the ISO 4401 hydraulic valve interface specification, matching the original Bosch Rexroth and Yuken dimensional standards.
Products are Intertek certified for high-pressure reliability, backed by a 1-year replacement warranty and reliable design service life. Standard orders ship from regular stock at Ningbo Port.
Related Models
More 4WE10 series models
Also in Rexroth-style directional valves