Home Full Catalog 4WE6J60/AW220N9Z5L
4WE6J60/AW220N9Z5L - Hydraulic Solenoid Valve by YXCHK
4WE6 Series

4WE6J60/AW220N9Z5L

Hydraulic Solenoid Valve model 4WE6J60/AW220N9Z5L - a Rexroth 4WE6 compatible hydraulic valve from YXCHK. Rated 31.5 MPa max pressure and 80 L/min max flow with DC 12/24V, AC 110/220V. 100% factory tested, 1-year warranty.

Max Pressure 31.5 MPa
Max Flow 80 L/min

Technical Datasheet

Specification ParameterTechnical Value
Nominal SizeNG6 / Cetop 3 / ISO 4401-03
Max Working Pressure31.5 MPa
Max T-Port Pressure16 MPa
Max Flow Rate80 L/min
Coil / ActuationDC 12/24V, AC 110/220V
Solenoid TypeWet solenoid, Z5L DIN connector, IP65
Spool FunctionsJ — P blocked, A and B open to T
Hydraulic FluidMineral oil HL/HLP per DIN 51524

Centre Condition & Cross-Reference

Spool FunctionJ
De-energised Flow PathP blocked, A and B open to T
Yuken Equivalent3C4

P is blocked while A and B are both connected to T. The pump is isolated from the circuit and both work lines drain to tank, so the actuator is driven in neither direction and a suspended load can settle. This is the float centre: pressure line sealed, both work ports vented.

Cross Reference

Direct drop-in replacement for Bosch Rexroth 4WE6 / 3WE6 series (WE6 ... /CG24N9Z5L and AW220N9Z5L coil variants). Same ISO 4401-03 mounting, no manifold modification required.

YXCHK Model4WE6J60/AW220N9Z5L
ReplacesRexroth 4WE6
Mounting StandardNG6 / Cetop 3 / ISO 4401-03
Voltage OptionsDC 12/24V, AC 110/220V

Spool Function & Control

Model 4WE6J60/AW220N9Z5L is a wet-armature solenoid directional valve in the 4WE6 family, a direct drop-in for Bosch Rexroth WE6 / 3WE6 units on the ISO 4401-03 (Cetop 3, NG6) mounting surface. It is one of 205 catalogued YXCHK models, and this page documents a single spool function — J — rather than the whole series. P is blocked while A and B are both open to T. The pump is isolated from the circuit and both work lines drain to tank. Wet solenoid construction keeps the coil immersed in hydraulic oil for heat dissipation, smooth switching and a design service life beyond reliables.

Mounting & Electrical

4WE6J60/AW220N9Z5L mounts on the same ISO 4401-03 subplate or manifold block, hole pattern unchanged. The AW220 coil is the 220 V AC wet-armature solenoid: an AC coil pulls in on a high inrush current and then holds on a much lower one once the armature is seated, so the seating stroke has to stay unobstructed for the valve to stay shifted. The coil ends in a Z5L DIN 43650 plug with indicator light, IP65 against dust and oil mist, and the N9 manual override allows hand operation during commissioning or fault-finding. Working fluid is mineral oil (HL/HLP) per DIN 51524, with 16 MPa maximum T-port back pressure.

Quality & Reliability

Each unit is run on the test bench in Taizhou before it is packed: the coil is energised, internal leakage is measured and the assembly is held at 31.5 MPa, and the sheet from that run stays attached to the batch record, so the history of any serial number survives. Valve bodies are cast iron, finished on CNC centres to a tolerance of +/- ISO 4401 mounting-face tolerances. Intertek certification, a one-year replacement warranty and an eight-year design life cover the range, orders are despatched from Ningbo Port within seven working days, and a single piece is a valid order quantity.

Where It Fits

Typical duty is high-cycle machine control: ram direction and pressure on hydraulic presses, spindle and tool-changer switching on CNC centres, actuator sequencing on automated lines. The 31.5 MPa rating puts it inside the range most stationary and mobile machinery runs at, while the oil-immersed solenoid keeps operation quiet and repeatable through continuous cycling. Send the model code you are replacing and the cross-reference is confirmed within 24 hours, free of charge.

Typical Applications

  • Hydraulic press machines - pressure and direction control
  • Machine tooling - high-frequency spindle switching
  • Automation lines - precise actuator logic control

Equivalent & Cross-Brand

Comparing brands before ordering? The full Rexroth 4WE6 equivalent table maps every spool function (E, G, H, J, L, M, U, F) against the Rexroth, Yuken and Vickers codes it replaces. For the swap procedure itself, see the Rexroth 4WE6 replacement guide.

Quality & Standards

Every YXCHK valve is 100% factory tested (electrical, leakage and max pressure) before shipment. Mounting patterns comply with ISO 4401 / DIN 24340 international standards, and the design follows the ISO 4401 hydraulic valve interface specification, matching the original Bosch Rexroth and Yuken dimensional standards.

Products are Intertek certified for high-pressure reliability, backed by a 1-year replacement warranty and reliable design service life. Standard orders ship from regular stock at Ningbo Port.

Related Models