Technical Guide • ISO 4401-03 • 31.5 MPa

Rexroth 4WE6 Replacement: Cross-Reference, Spool Function Matching and Factory Test Standards

A practical engineering guide from the YXCHK technical team in Taizhou, Zhejiang, for OEMs, distributors and MRO buyers sourcing an equivalent for the Rexroth 4WE6 series directional control valve.

1. Why the 4WE6 Is the Most-Replaced Directional Valve

The Rexroth 4WE6 is a solenoid-operated directional spool valve with a nominal size of NG6, mounted to the ISO 4401-03 interface. Because that interface is standardised, the valve appears in machine tools, injection moulding machines, blow moulding lines, presses and general hydraulic power units in very high volumes. When a machine is out of production, the buyer needs a valve that bolts to the same subplate, uses the same solenoid voltage and reproduces the same spool function — not a redesign.

That is the entire scope of a 4WE6 replacement: identical mounting pattern, identical port logic, compatible flow and pressure rating, and a coil that matches the machine's control voltage. Everything else, including the model code printed on the body, is a commercial and documentation question, not a hydraulic one.

2. What Must Match Before You Substitute

Parameter What to verify
InterfaceISO 4401-03 (NG6) 4-port mounting pattern, 4 x M5 fixing bolts
Spool functionCentre condition and port logic — see the function table in section 3
Number of positions2-position or 3-position, spring return or spring centred or detent
Coil voltageDC 12 V / 24 V, or AC 110 V / 220 V — must match the machine control output
Electrical connectionDIN 43650 plug-in connector vs. terminal box; check cable entry direction
Pilot and drainInternal pilot / internal drain is the default; external pilot or external drain only where the circuit requires it
T-port back pressureConfirm the allowable back pressure at T against the valve datasheet for the circuit in question

3. Spool Function Cross-Reference

The single most common substitution error is matching the model number while ignoring the spool function. A 4WE6 in the wrong centre condition will bolt up perfectly and behave incorrectly. The table below maps the Rexroth function letter to the YXCHK model and the corresponding Yuken DSG-01 function code.

Function Centre condition YXCHK Model Rexroth Equivalent Yuken DSG-01
EAll ports closed4WE6E60/CG24N9Z5L4WE6E6X/EG24N9K43C2
GP to T, A and B blocked4WE6G60/CG24N9Z5L4WE6G6X/EG24N9K43C60
HAll ports open to T4WE6H60/CG24N9Z5L4WE6H6X/EG24N9K43C3
JP blocked, A/B to T4WE6J60/CG24N9Z5L4WE6J6X/EG24N9K43C4
LA to T, B and P blocked4WE6L60/CG24N9Z5L4WE6L6X/EG24N9K43C12
MT closed, A/B/P open4WE6M60/CG24N9Z5L4WE6M6X/EG24N9K43C9
UB to T, A and P blocked4WE6U60/CG24N9Z5L4WE6U6X/EG24N9K43C10
FP to B, A to T4WE6F60/CG24N9Z5L4WE6F6X/EG24N9K43C5

Parker D1VW equivalents follow a different numbering logic: D1VW006 corresponds to the M function, and D1VW007 corresponds to the F function. Vickers DG4V-3 codes should always be confirmed against the specific spool drawing before ordering.

4. Reading the Model Code

Take 4WE6E60/CG24N9Z5L as a worked example. 4WE6 is the series and nominal size. E is the spool function. 60 is the series index. CG24 denotes a DC 24 V coil with a DIN plug-in connector. N9 indicates the electrical option. Z5L covers the manual override and seal variant. This is the YXCHK ordering code; the Rexroth equivalent for the same duty is 4WE6E6X/EG24N9K4.

When requesting a quotation, sending the complete code as printed on the existing valve body is faster and safer than describing the function in words. If the nameplate is illegible, photograph the spool symbol from the valve side and state the coil voltage — that is enough to identify the correct replacement.

5. How YXCHK Tests Each Valve Before Dispatch

YXCHK is a directional control valve manufacturer operating from a facility of approximately 2,400 m² in Luqiao District, Taizhou, Zhejiang. Valve bodies are machined on our own CNC line rather than bought in finished, which is what allows us to hold bore geometry and finish consistently across a production run. After machining, bodies are deburred, ultrasonically cleaned and assembled at bench stations.

  • —Pressure test at the series rating — 31.5 MPa for the Rexroth-compatible series, 21 MPa for the Yuken-compatible series — applied to every individual valve, not to a sample batch.
  • —Leakage check on the closed ports to confirm the spool-to-bore fit holds.
  • —Electrical and shift function test to confirm both solenoids operate and the spool returns correctly.

Third-party verification is available: Intertek carried out a factory audit, report number 492803054_P+T. The company holds registered trademark No. 15725263 for YXCHK and utility model patent CN222823457U for a pneumatic control device for a hydraulic directional valve.

6. Common Questions

Is a 4WE6 replacement a direct bolt-on?

Yes, provided the mounting interface is ISO 4401-03 and the spool function matches. The fixing bolt pattern and port positions are dimensionally standard, so the valve mounts to the existing subplate without modification.

Can I mix a 24 V DC coil with an existing AC circuit?

No. The coil must match the control voltage and current type supplied by the machine. Confirm the voltage from the nameplate or the control cabinet output before ordering.

What is the difference between internal and external pilot?

Internal pilot takes pilot pressure from the P port and is the standard configuration for most circuits. External pilot is used where system pressure is too low or too variable to shift the spool reliably. The general rule on drain is that a valve marked with external drain must have its T line returned separately.

Do you supply the subplate and mounting bolts?

Subplates, modular stack valves and complete manifold blocks are available on request. Send the circuit drawing and we will quote the assembly rather than the valve alone.

Continue Reading