Home Full Catalog 4WE10HA30B/AW220N9Z5L
4WE10HA30B/AW220N9Z5L - Hydraulic Solenoid Valve by YXCHK
4WE10 Series

4WE10HA30B/AW220N9Z5L

Hydraulic Solenoid Valve model 4WE10HA30B/AW220N9Z5L - a Rexroth 4WE10 compatible hydraulic valve from YXCHK. Rated 31.5 MPa max pressure and 120 L/min max flow with DC 24V, AC 220V. 100% factory tested, 1-year warranty.

Max Pressure 31.5 MPa
Max Flow 120 L/min

Technical Datasheet

Specification ParameterTechnical Value
Nominal SizeNG10 / Cetop 5 / ISO 4401-05
Max Working Pressure31.5 MPa
Max T-Port Pressure16 MPa
Max Flow Rate120 L/min
Coil / ActuationDC 24V, AC 220V
Solenoid TypeWet solenoid, low-noise, N9 manual override
Spool FunctionsHA — P, A, B and T all interconnected
Hydraulic FluidMineral oil HL/HLP per DIN 51524

Centre Condition & Cross-Reference

Spool FunctionHA
De-energised Flow PathP, A, B and T all interconnected
Yuken Equivalentequivalent code on request

HA is the single-solenoid conversion of spool H on the same spool. At centre all four ports are interconnected - P, A, B and T equalise - so the pump discharges to tank and both work lines are vented to the same low pressure, leaving the actuator free to float. The spring returns the spool to this open centre whenever the coil is de-energised, and because there is a single coil the valve cannot stay shifted after the supply is cut.

Cross Reference

Drop-in replacement for Bosch Rexroth 4WE10 / 3WE10 series. NG10 / Cetop 5 / ISO 4401-05 mounting, 100% interchangeable.

YXCHK Model4WE10HA30B/AW220N9Z5L
ReplacesRexroth 4WE10
Mounting StandardNG10 / Cetop 5 / ISO 4401-05
Voltage OptionsDC 24V, AC 220V

Spool Function & Control

Model 4WE10HA30B/AW220N9Z5L is an NG10 (Cetop 5, ISO 4401-05) wet-armature solenoid directional valve engineered as a direct replacement for the Bosch Rexroth 4WE10 / 3WE10 series on the ISO 4401-05 mounting surface. It is one of 205 catalogued YXCHK models, and this page documents a single spool function — HA — rather than the whole series. P, A, B and T are all interconnected, the same centre as spool H. The pump discharges to tank and both work lines are vented to the same low pressure. The 10 mm bore with a hardened, precision-ground spool delivers stable high-flow switching with minimal pressure ripple, and wet solenoid construction keeps the coil in oil for heat dissipation and a design service life beyond reliables.

Mounting & Electrical

4WE10HA30B/AW220N9Z5L fits the same ISO 4401-05 interface, hole pattern unchanged. The AW220 coil is the 220 V AC wet-armature solenoid: an AC coil draws a high inrush current on pull-in and then a much lower holding current once the armature seats, so the seating stroke must not be obstructed or the valve will chatter on a 10 mm bore. The coil terminates in a Z5L DIN 43650 plug with indicator light, IP65 rated, and the N9 manual override covers commissioning and fault-finding. Working pressure is 31.5 MPa, rated flow 120 L/min, maximum T-port back pressure 16 MPa, with mineral oil HL/HLP to DIN 51524.

Quality & Reliability

Each unit is run on the test bench in Taizhou before it is packed: the coil is energised, internal leakage is measured and the assembly is held at 31.5 MPa, and the sheet from that run stays attached to the batch record, so the history of any serial number survives. Valve bodies are cast iron, finished on CNC centres to a tolerance of +/- ISO 4401 mounting-face tolerances. Intertek certification, a one-year replacement warranty and an eight-year design life cover the range, orders are despatched from Ningbo Port within seven working days, and a single piece is a valid order quantity.

Where It Fits

Typical service is heavy machinery with large actuators - forging presses, injection moulding clamp systems, industrial compactors and marine winching. The valve is rated 31.5 MPa with 120 L/min through an NG10 bore, which gives the flow headroom multi-actuator circuits need, while the wet armature keeps operation quiet and repeatable under continuous cycling. The cross-reference is confirmed within 24 hours from the original model code, free of charge.

Typical Applications

  • Heavy forging presses - high-flow directional control
  • Plastic machinery - injection molding clamp systems
  • Waste compactors - high-power reciprocating actuators

Quality & Standards

Every YXCHK valve is 100% factory tested (electrical, leakage and max pressure) before shipment. Mounting patterns comply with ISO 4401 / DIN 24340 international standards, and the design follows the ISO 4401 hydraulic valve interface specification, matching the original Bosch Rexroth and Yuken dimensional standards.

Products are Intertek certified for high-pressure reliability, backed by a 1-year replacement warranty and reliable design service life. Standard orders ship from regular stock at Ningbo Port.

Related Models