4WEH16E50/CG24N9Z5LET
Electro-Hydraulic Valve model 4WEH16E50/CG24N9Z5LET - a Rexroth 4WEH16 compatible hydraulic valve from YXCHK. Rated 31.5 MPa max pressure and 300 L/min max flow with DC 24V, AC 220V. 100% factory tested, 1-year warranty.
Technical Datasheet
| Specification Parameter | Technical Value |
|---|---|
| Nominal Size | NG16 / Cetop 7 / ISO 4401-07 |
| Max Working Pressure | 31.5 MPa |
| Max T-Port Pressure | 16 MPa |
| Max Flow Rate | 300 L/min |
| Coil / Actuation | DC 24V, AC 220V |
| Solenoid Type | Pilot-operated, internal/external pilot & drain options |
| Spool Functions | E — all ports blocked (P, A, B and T mutually isolated) |
| Hydraulic Fluid | Mineral oil HL/HLP per DIN 51524 |
Centre Condition & Cross-Reference
| Spool Function | E |
| De-energised Flow Path | all ports blocked (P, A, B and T mutually isolated) |
| Yuken Equivalent | 3C2 |
With both solenoids de-energised, P, A, B and T are mutually isolated. Pressure cannot reach either work port and neither work port can drain, so a cylinder or motor connected to A and B stays locked while the pressure line is sealed inside the valve. This is the blocking centre: the load is held after the pump stops and nothing drifts while the valve sits centred.
Cross Reference
Drop-in replacement for Bosch Rexroth 4WEH16 / 4WEH... series with ET/E/T pilot control codes.
| YXCHK Model | 4WEH16E50/CG24N9Z5LET |
| Replaces | Rexroth 4WEH16 |
| Mounting Standard | NG16 / Cetop 7 / ISO 4401-07 |
| Voltage Options | DC 24V, AC 220V |
Pilot & Spool Control
Model 4WEH16E50/CG24N9Z5LET is an electro-hydraulic (pilot-operated) directional valve in the 4WEH16 family, directly interchangeable with the Bosch Rexroth 4WEH16 series on the ISO 4401-07 (Cetop 7, NG16) interface. It is one of 205 catalogued YXCHK models, and this page documents a single spool function — E — rather than the whole series. With both solenoids de-energised, P, A, B and T are mutually isolated. Pressure cannot reach either work port and neither work port can drain back to tank. The trailing ET in the ordering code sets this valve's pilot and drain configuration. A small pilot stage drives the main NG16 spool, so flows of 300 L/min and above are switched by low-power solenoid signals, and the internal/external pilot and drain options (E / T / ET) let the control-oil supply match the original configuration code.
Mounting & Electrical
4WEH16E50/CG24N9Z5LET mounts to the ISO 4401-07 (NG16) interface with the same bolt pattern and porting as the original, so no manifold changes are required. The pilot solenoid uses a Z5L DIN 43650 connector rated IP65; a DC coil draws a steady current through the whole stroke, so the pilot stage shifts with the same force at rest and at full travel. Main-stage working pressure reaches 31.5 MPa with a 300 L/min rated flow and 16 MPa maximum T-port pressure, and the cast-iron body is machined to a tolerance of +/- ISO 4401 mounting-face tolerances for leak-free sealing under heavy cyclic load.
Quality & Reliability
Each unit is run on the test bench in Taizhou before it is packed: the coil is energised, internal leakage is measured and the assembly is held at 31.5 MPa, and the sheet from that run stays attached to the batch record, so the history of any serial number survives. Valve bodies are cast iron, finished on CNC centres to a tolerance of +/- ISO 4401 mounting-face tolerances. Intertek certification, a one-year replacement warranty and an eight-year design life cover the range, orders are despatched from Ningbo Port within seven working days, and a single piece is a valid order quantity.
Where It Fits
Duty is heavy and continuous - deck winches and anchor gear, crusher circuits, metallurgical line actuators, large press installations. Because a small pilot stage shifts the main NG16 spool, a low-power solenoid signal is enough to switch flows of 300 L/min and above. Quote the existing code and the cross-reference comes back within 24 hours, at no charge.
Typical Applications
- Marine & offshore - anchor winches and deck machinery
- Mining equipment - roof supports and crushers
- Metallurgy - steel production line drives
Quality & Standards
Every YXCHK valve is 100% factory tested (electrical, leakage and max pressure) before shipment. Mounting patterns comply with ISO 4401 / DIN 24340 international standards, and the design follows the ISO 4401 hydraulic valve interface specification, matching the original Bosch Rexroth and Yuken dimensional standards.
Products are Intertek certified for high-pressure reliability, backed by a 1-year replacement warranty and reliable design service life. Standard orders ship from regular stock at Ningbo Port.
Related Models
More 4WEH16 series models
Also in Rexroth-style directional valves